Cisco 642-813

Thoughtful online customer service

Nowadays, online shopping has been greatly developed, but because of the fear of some uncontrollable problems after payment, there are still many people don't trust to buy things online, especially electronic products. But you don't have to worry about this when buying our 642-813 actual exam. Not only will we fully consider for customers before and during the purchase, but we will also provide you with warm and thoughtful service after payment. We have a special technical customer service staff to solve all kinds of consumers’ problems. If you have questions when installing or using our 642-813 practice engine, you can always contact our customer service staff via email or online consultation. They will solve your questions about 642-813 preparation materials with enthusiasm and professionalism, giving you a timely response whenever you contact them.

Carefully written content

In order to ensure the quality of our 642-813 preparation materials, we specially invited experienced team of experts to write them. The content of our 642-813 practice engine comes from a careful analysis and summary of previous exam syllabus, so that you can accurately grasp the core test sites. In general, our 642-813 actual exam has covered all the knowledge that must be mastered in the exam. You just should take the time to study 642-813 preparation materials seriously, no need to refer to other materials, which can fully save your precious time. To keep up with the changes of the exam syllabus, our 642-813 practice engine are continually updated to ensure that they can serve you continuously.

As we all know, sometimes the right choice can avoid the waste of time, getting twice the result with half the effort. Especially for 642-813 preparation materials, only by finding the right ones can you reduce the pressure and help yourself to succeed. If you haven't found the right materials yet, please don't worry. Maybe our 642-813 practice engine can give you a leg up which is our company's flagship product designed for the 642-813 exam. No matter which country or region you are in, our 642-813 can provide you with thoughtful services to help you pass exam successfully. They have many advantages, and next I'll introduce them to you.

Making your learning time-saving and efficient

Generally speaking, preparing for the 642-813 exam is a very hard and even some suffering process. Because time is limited, sometimes we have to spare time to do other things to review the exam content, which makes the preparation process full of pressure and anxiety. But from the point of view of customers, our 642-813 actual exam will not let you suffer from this. As mentioned above, our 642-813 practice engine have been carefully written, each topic is the essence of the content. Only should you spend about 20 - 30 hours to study 642-813 preparation materials carefully can you take the exam. The rest of time you can go to solve all kinds of things in life, ensuring that you don't delay both study and work.

Cisco Implementing Cisco IP Switched Networks Sample Questions:

1. Which two characteristics apply to Cisco Catalyst 6500 Series Switch supervisor redundancy using NSF? (Choose two.)

A) independent of SSO
B) uses the FIB table
C) prevents route flapping
D) supports IPv4 and IPv6 multicast
E) supported by RIPv2, OSPF, IS-IS, and EIGRP
F) NSF combined with SSO enables supervisor engine load balancing

2. When configuring private VLANs, which configuration task must you do first?

A) Disable IGMP snooping.
B) Configure and map the secondary VLAN to the primary VLAN.
C) Configure the private VLAN port parameters.
D) Set the VTP mode to transparent.

3. Which of the following specifications is a companion to the IEEE 802.1w Rapid Spanning Tree Protocol (RSTP) algorithm, and warrants the use multiple spanning-trees?

A) Cisco PVST+
B) IEEE 802.1Q (CST)
C) IEEE 802.1d (STP)
D) None of the other alternatives apply
E) IEEE 802.1s (MST)

4. CORRECT TEXT

Each of these vlans has one host each on its ports
SVI on vlan 1 - ip 192.168.1.11 Switch B -Ports 3, 4 connected to ports 3 and 4 on Switch A
Port 15 connected to Port on Router.
Tasks to do:
1.Use non proprietary mode of aggregation with Switch B being the initiator -- Use LACP with B being in Active mode
2.Use non proprietary trunking and no negotiation -- Use switchport mode trunk and switchport trunk encapsulation dot1q
3.Restrict only to the VLANs needed -- Use either VTP pruning or allowed VLAN list. The preferred method is using allowed VLAN list
4.SVI on VLAN 1 with some ip and subnet given
5.Configure switch A so that nodes other side of Router C are accessible -- on switch A the default gateway has to be configured.
6.Make switch B the root

5. DRAG DROP
This is a drag and drop question which is about the correct sequence of steps that a wireless client takes during the process of association with an access point (AP). Drag the items to the proper locations.

Solutions: